Even if Boss pedals represent the anti-thesis of handmade boutique pedals, most of us are still using at least one of them. This is why the release of new models is always an important event.
This September, Boss is adding two new pedals to its arsenal: the ST-2 Power Stack and the PS-6, a long overdue replacement to the PS-5 Pitch Shifter.
The ST-2 is a modeling pedal which emulates the sound of a big amplifier and features a “sound” knob that changes the character of the tone. The PS-6 is a pitch shifter pedal that can do two part harmonies and it seems the tracking is just spot on.
Metal guitar virtuoso Marty Friedman demonstrates these two pedals here. The only other effect I hear is a delay and you have to admit the tones he is getting are killer:
With the ever growing number of pedals in our rigs, issues often arise such as tap dancing to switch between different sounds, powering all our beloved stompboxes as well as the introduction of noise or hum in the tone. I recently stumbled upon the website of The Gig Rig and from what I can see, this is a company that probably addresses every issue associated with building a complex guitar rig. It prompted me to write a post about organizing and powering our pedals.
The Gig Rig products help you organize and power all your pedals - Picture courtesy of The Gig Rig
Switching
In order to turn multiple pedals on and off, The Gig Rig offers a number of programmable “Loop Switcher” floorboards.
The idea is quite simple, these machines have a number of effect loops in which you insert your effect units or pedals. They work like the effect loop on your amp except that on the Gig Rig loop switchers, you can have up to 10 of them. And even better, you can program presets such as “pedal in effect loop 1 + pedal in effect loop 3” and recall these presets by pressing a switch. In other words, it turns a bunch of pedals into a programmable multi-effect unit.
Here is a video demo of the Gig Rig flagship Pro 14 loop switcher which offers no less that 10 loops and 14 presets:
The Pro 14 comes with a power supply to power all these pedals and has some neat features such as the possibility to correct volume mismatches between pedals, the possibility to choose between buffered or true bypass signal paths or two outputs if you use two amplifiers.
The Gig Rig offers another 3 loop switchers:
the Midi 8 which is a 6 loops/10 preset version of the Pro 14 minus the true bypass/buffered signal paths feature
the Loopy-2 is a simple 2 loop non programmable switcher (same idea as the Boss LS-2 without the volume control)
The Remote Loopy-2 is the same as the Loopy-2 except that the switch can be “deported” so that you can leave the switcher near the effect loop of your amp
Often, a poor choice of wall wart adapters to power your pedals can significantly alter the quality of your tone. Granted this is not the only reason for getting hum but it is an easily fixable one.
Although it is not a novel idea, The Gig Rig has refined the idea of a power supply capable of powering many pedals. The Generator in itself is a power supply that provides up to 5A of power which is more than enough to power all your pedals. It comes with daisy chain Boss style cables.
That would be pretty boring without the available isolated adapters which allows to power any type of pedal on the planet such as 12V (TC Electronic Nova Delay), 15V, 18V or even 24V.
The Generator power supply...
...And its adapters
Even better, the Virtual Battery adapter will make your pedals believe they are powered by a battery. Perfect to power a vintage pedal!
Finally, for those of you with ground problems, the Hum Dinger provides an isolated output.
The Gig Rig website is full of advice and information about pedals and building rigs, it is well worth a read.
Alternatives: when looking for a pedal power supply, companies to consider include CIOKS (I personnally own a Big John which can power up to seven 9V pedals and it has been very good) and Voodoo Lab with their famous Pedal Power line of products.
There is a lot of effects that fall under the “modulation” category on the ground that they send your tone swirling or oscillating. In this series of posts, I will try to unravel the mysteries of effects such as phaser, flanger, chorus, leslie/univibe, vibrato or tremolo. These effects, if used well, can spice up your rythm work or make your lead tone fatter to name only two of their magical powers. I will not go into too much details about the electronics behind these effects but will focus on their characters and uses for us, guitarists. Videos are included to stir up your inspiration.
In this first part, I will present one of the oldest modulation effects: the Phaser also known as Phasing or Phase-Shifting.
The MXR Phase 90, one of the most famous phaser pedals - Photo by Pia Jane Bijkerk
Phaser or Flanger?
The first thing I should clear up is the difference between phaser and flanger as I often see in forums that people get confused. Phasing is created by using a series of filters (all pass filters) associated with an oscillator whereas flanger is created by using a very short delay. I am over simplifying here but know that they do sound different. Phasing tends to sound a little “crazier” and has no real equivalent in the real world. Flanging, on the other hand, sounds like a jet plane taking off and is akin to a real world sound effect known as “Doppler”. I will write about flanging in part 2 and focus on phasing in this post. For those of you wanting to know more about the science and the electronics behind our beloved phaser pedals, have a look at this wikipedia page.
Who uses a phaser?
The phaser effect is used in almost every genre but some are more phaser friendly than others. Used with a non distorted clean tone, it is for instance very popular in reggae: listen to the solo of “No Woman No Cry” on the live at the Lyceum by Bob Marley for a prime example of phased guitar.
Funk is also a genre where phasing is king. It enhances rhythm licks and can be an alternative to a Wah (although they are two different things).
When it comes to big rock tones, Brian May of Queen and of course Eddie Van Halen are big phaser users. The first Van Halen album is almost a demo of the MXR Phase 90, listen to the Intro of “Atomic Punk” or “Ain’t Talking about Love” and you’ll know what I mean.
Timeless Classics: the MXR Phase 90
You will find information about other models after the videos below but I have decided to present and demonstrate the MXR Phase 90 first. This little orange pedal is to phasers what the Tube Screamer is to overdrives: the standard. I have recently acquired a vintage phase 90 and I must say the hype is not unfounded. It is really warm and although it has only one setting (“speed”), you can get a lot of different sounds out of it. With the speed setting between 10 o’clock to 12, it goes straight into Van Halen territory whereas at higher speeds, around 2 o’clock, it is reminiscent of some tones Hendrix got with his univibe pedal.
If you are in the market for a Phase 90, it can get confusing as there are several models to choose from. The very first 1970s unit had no LED and “Phase 90” was written using a type of “handwriting” imitation. Thus, these pedals are nicknamed “Script”. Around the end of the 70s, the lettering changed to capital letters and these models are nicknamed “Block”. The sound did not change much between these two early versions though.
MXR went bust in the 80s and the brand was resuscitated by Dunlop. No less than three versions of the Phase 90 are currently manufactured by MXR. The entry model, orange with a LED and “Block Lettering” is the most affordable. The thing is it does not sound quite like the old stuff and tends to provide a more “pronounced”, less subtle phasing effect. In order to address these issues, MXR also sells a reissue model which sports a “Script” logo and has no LED or external power plug. It does sound more subtle and is closer to the old 70s models.
The third model in the range, the Eddie Van Halen or EVH Phase 90 has a little switch to go from a modern “Block” tone to a more subtle vintage “Script” sound. A fourth custom shop model was sold until recently, it was orange, with Script lettering and a led and its model number is CSP-101. People who have opened it apparently found out that it was an EVH model without the block/script switch which seems quite redundant to me and might explain why it seems difficult to find it anywhere. For a sound comparison between the entry level “Block” Phase 90 and the Custom Shop “Script” model, have a look at this video by gearmanndude.
Phase 90 Video Demos
Here are three videos showing my Vintage MXR Phase 90 in action: first clean then placed before the distortion and finally after the distortion. I show different settings in each video and at the end, I add a little delay using my Boss DD-3 to show how it plays with a phaser for an ultra spacious tone.
Phase 90 with fairly clean amp first:
Gear used for the video: Fender American Classics Custom Shop Stratocaster with Kinman AVn Blues pickups, 1974 Fender Champ Amplifier (Volume at 3, Bass at 10, Treble at 2.5).
And now placed before a distortion. Note how the 10 o’clock speed setting is very Van Halen-esque whereas the 2 o’clock setting goes into Hendrix territory:
Gear used for the video: Fender American Classics Custom Shop Stratocaster with Kinman AVn Blues pickups, 1974 Fender Champ Amplifier (Volume at 3, Bass at 10, Treble at 2.5), Analogman modded Boss DS1 Distortion (Dist at Max, Tone at 8 o’clock and Level at 10 o’clock).
Finally, here is how it sounds placed after the distortion. Note how more pronounced the effect is. I personally prefer to place it before the distortion:
Gear used for the video: Fender American Classics Custom Shop Stratocaster with Kinman AVn Blues pickups, 1974 Fender Champ Amplifier (Volume at 3, Bass at 10, Treble at 2.5), Analogman modded Boss DS1 Distortion (Dist at Max, Tone at 8 o’clock and Level at 10 o’clock).
Alternatives to a Phase 90
There are other models than the MXR Phase 90 but before you choose a phaser pedal, you have to know that phasers have a certain number of “filter stages” (remember, phasers are built using a series of filters). The number of stages has a great influence on the tone. In some ways, the more stages, the more pronounced the effect. Basic phasers such as the recently reissued MXR Phase 45 have only two stages and they are quite gentle. 4 stage phasers are the most commonly heard on records, uber famous examples are the MXR Phase 90 or the Electro Harmonix Small stone, both used by David Gilmour in the 70s. If you want that classic 70s phaser tone, chances are you will want a 4 stage phaser.
Companies like Boss went further with their phasers and the now discontinued PH-2 had 10 or 12 stages depending on the position of its mode button. I own a PH-2 and although it is not a bad phaser, it tends to sound quite out-worldly and I find difficult to use it to reproduce the Van Halen rock tone or the cleaner reggae/ 70s funk tone. The replacement of the PH-2 in the Boss line, named PH-3, is a digital pedal and can emulate the tone of 4, 8, 10 and 12 stage phasers. I haven’t tried it but I gather from various sources that it is versatile if not very warm sounding.
The settings on a phaser can go from only one speed button (MXR Phase 90 or 45) which decides how fast the tone “swirls” to three knobs called Depth, Rate an Resonance (Boss models). Depth is the ratio between processed and unprocessed sound, Rate is the speed of the oscillations and Resonance is a setting that allows to take some of the processed signal and send it back to be phased again which creates super crazy effects.
There is a bit of a debate as to where to place a phaser in the effect chain. In most multi-effect units, it is placed after the overdrive/distortion stage but I must say that I got very good results by placing my Phase 90 before a distortion as seen in the videos above. As always, experiment!
Let’s also not forget that phasing sounds great with keyboards, especially with Fender Rhodes electric piano sounds as well as pads. It even sounds good with bass! If you lend your phaser to your keyboardist or bassist, he/she might not want to give it back, you are warned!
Other noteworthy phaser models
On the second hand market, another great model is the Maestro PS-1, good luck to find one. As far as I know there is no clone on the market.
Boutique manufacturers have also come up wit great models such as the Retro-sonic Phaser which is an MXR Phase 90 clone with more settings. Let’s also mention the Pigtronix EP1 which is as whacky as it gets.
Finally, for those on a budget, the Ibanez PH7 is a good alternative with 4 and 8 stage modes.
In Part 1 of this series of posts dedicated to the use of delay, I have shown how to create rhythmical effects “à la U2” by synchronizing the delay to the tempo of a song. Today, in Part 2, I will first give you a few example settings showing how to fatten your tone using a Boss DD-3 and an Electro Harmonix Deluxe Memory Man. After the videos, I will explain the differences between analog and digital delays as they both have distinct sounds and when it comes to choosing a delay pedal, the analog versus digital debate is still very much alive!
Fattening your tone: the “guitar hero” delay effect
Here is a personal favorite of mine, the type of delay that countless 80s guitarists used pretty much all the time to season their fierce solos. I have reproduced it using a Digital Boss DD-3 as well as an Analog, darker sounding Electro Harmonix Deluxe Memory Man:
Gear used: American Classics Stratocaster with Kinman pickups -> Analogman TS9 -> Proco RAT 2 -> Marshall JMP-1 preamp plugged direct into the recorder
To recreate this type of delay using a software plugin or multi-effect, set a delay time around 350 ms, 3 or 4 repetitions and a mix level of about 25%. Results may vary depending on your exact equipment. As always, experiment to find out what you are most confident with and most importantly what the song you are working on exactly needs.
Fattening your tone: the slapback echo
I have written a complete post about it so I will only give the audio examples here. The slapback echo is the “mother of all delays”. It consists of only one short repetition. As simple at it may seem, it is a very effective tool as shown in this video:
In the video, the slapback delay is generated using Cubase 5’s delay plugin with the following settings:
You can achieve the same type of tone with a Boss DD-3 and the following settings: Mode 200ms, E.LEVEL at 12 o’clock, F.BACK at 9 o’clock and D.TIME at 4 o’clock. You might want to vary the E.LEVEL or D.TIME to taste. It is easy to reproduce this effect with any other model of delay, just set the “delay time” between 70 and 200ms and the “feedback” quite low in order to have just one repeat.
Fattening your tone: Multitap delays
When one delay is not enough, use several of them! Known as “Multitap Delay”, the use of two or more delay units multiply the possibilities. Here I show the Boss DD-3 and the Electro Harmonix Memory Man together. Note that I had to reduce the delay time on the DD-3 compared to the first video, reason being that the previous settings were too close to the Memory Man and did not create enough of a swirl:
Gear used: American Classics Stratocaster with Kinman pickups -> Analogman TS9 -> Proco RAT 2 -> Marshall JMP-1 preamp plugged direct into the recorder
Again experimenting is the key here. I have used two delay settings that were quite similar but you can also use two delays with very different settings like a short one and a long one. At some stage, Joe Satriani was using three delays at once: one with a short delay time, another one with a medium delay time and a third one with a long delay time. It gave his tone almost a reverb like feeling.
The Analog vs Digital Debate
After seeing these demos you might want to go shopping for a delay pedal and must be wondering: “analog or digital?”. We have to go back in time in order to understand why there are several types of delays on the market.
